No Reserve 7" x 17" & 8" x 17" Kinesis/BW Motorsports 3.6 Cup Style 3-Piece Wheels
Final bid: $1,935 Sold
Item Details
- Seller: Lambogas
- Location: Harris County, Texas 77373
- Lot #: P-0017617
Available for auction is a set of 7" x 17" & 8" x 17" Kinesis/BW Motorsport Cup style 3-piece wheels. The seller states the wheels are in excellent condition and are free of any damage. Included with the wheels are a set of step lips for wider fitment as well as both a silver set and gold set of wheel hardware. These wheels are best suited 964 models but will fit multiple Porsche vehicles, but please confirm fitment on your vehicle before bidding. The buyer is responsible for shipping, handling, and fees.
Front Wheel:
7" x 17"
Rear Wheel:
8" x 17"
Auction Results
- Sold for: $1,935
- Auction End: Mar 31, 2022 09:03:49PM UTC
- Number of Bids: 49
Comments (66)
Sold for $1,935
dont understand how I had high bid of $1925 at 0 min 0 seconds, then "please wait" and all the sudden boom $1935 and count down again?
Bid in the amount of $1,935
Bid in the amount of $1,925
Bid in the amount of $1,900
Bid in the amount of $1,885
Bid in the amount of $1,875
Bid in the amount of $1,860
Bid in the amount of $1,850
Bid in the amount of $1,830
Bid in the amount of $1,820
Bid in the amount of $1,800
Bid in the amount of $1,750
Bid in the amount of $1,720
Bid in the amount of $1,710
Bid in the amount of $1,700
Bid in the amount of $1,660
Bid in the amount of $1,650
Bid in the amount of $1,630
Bid in the amount of $1,620
Bid in the amount of $1,610
Bid in the amount of $1,600
Bid in the amount of $1,560
Bid in the amount of $1,550
Bid in the amount of $1,510
Bid in the amount of $1,500
Bid in the amount of $1,450
Bid in the amount of $1,440
Bid in the amount of $1,430
Bid in the amount of $1,410
Bid in the amount of $1,400
Bid in the amount of $1,380
Bid in the amount of $1,360
Bid in the amount of $1,350
Bid in the amount of $1,300
Bid in the amount of $1,270
Bid in the amount of $1,260
Bid in the amount of $1,230
Bid in the amount of $1,220
Bid in the amount of $1,210
Bid in the amount of $1,200
Bid in the amount of $1,160
Bid in the amount of $1,150
@tfroeh8 …. He had a 964 at the time but these a little too wide
Did you ever find out what car the owner planned to use these wheels for?
@yoshjgg .... They both measure 2" and you also have the widebody lips that would make the rear 2 1/2"
Bid in the amount of $1,100
@Lambogas thanks. Also how many inches deep are the outer lips on both fronts & rears?
Bid in the amount of $1,050
Bid in the amount of $1,000
Bid in the amount of $800
@yoshjgg ..... That is correct
@Lambogas please confirm bolt pattern is 5x130. Thanks.
Bid in the amount of $600
Bid in the amount of $500
Bid in the amount of $400
@tfroeh8 ...... These belonged to a very long term customer that never put them on a car, he has owned over 25 porsches over the years ... from 930s to 964s to 993s to GT2RSs .... He is out of town until tomorrow but I will find out what his intentions were.
We’re these previously used on a 964? If so the ET would be between 50 and 55, which was the ET for the various wheels that were available on the 964s. I know this because I have a 964 and researched this when I was looking for wheels to replace the ones that came with the car.
@linderpat .... They are not cast on the spokes .... We laid the wheel flat on the ground and using 2 straight edge rulers measured from the ground to the lip .... divided that by 2 and then measured from the mounting hub to the lip just as it says to do in the video to find the ET
Seller - the offsets are the ET numbers, and should be cast into the spokes of the wheels. What are the ET numbers. I don't know how you came up with your numbers, but offset is critical in order to know what these wheels will fit, what spacers are needed, etc. I may bid depending on the offsets (the ET numbers for front and rear).
@linderpat ..... What I have come up with is the front is a 32MM offset and the rear is 25MM
That is without the widebody lip for the rears
Seller, you will do significantly better here if you list the offsets. Nobody is going to buy these unless they have that basic data, or a 964. There is no way to determine what else they'll fit without that information.
@JustOneMore ..... After some back and forth they are 17s
I did a measurement and from the the mounting hub to the wheel lip is 6"
@JustOneMore .... I believe that was a mistake about the 17"
If you look at the bottom photo to the right you can see the tape measure
Sorry but what does the ET stand for?
title says 17" but below says 18" ?
Also do you know the ET for these wheels ?
Bid in the amount of $25